PRESSURE SENSITIVE ADHESIVES
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYBUTENES/RESIN)
| Sl. | Raw Materials | Percent by Weight |
| 1. |
Vistanex MML-100 Isobutene Polymer |
35.0 |
| 2. |
Polybutene 128 Isobutene Polymer |
18.0 |
| 3. |
Abitol Resin |
21.0 |
| 4. |
Mineral Oil |
26.0 |
| |
|
100.0 |
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLBUTENES/RESIN)
.
| Sl. | Raw Materials | Per cent by Weight |
| 1. |
Vistanex MML-100 Isobutene Polymer |
35.0 |
| 2. |
Polybutene 128 Isobutene Polymer |
22.0 |
| 3 |
Staybelite Ester 3 Resin |
17.0 |
| 4. |
Mineral Oil |
26.0 |
| |
|
100.0 |
HOT MELT PRESSURE SENSITIVE ADHESIVE(POLUBUTENES/RESINS)
td] 36.0
| Sl. | Raw Materials | Per centby Weight |
| 1. |
Vistanex MML-100 Isobutene Polymer |
| 2. |
Polybutene 128 Isobutene Polymer |
10.0 |
| 3. |
Staybelite Ester 3 Resin |
18.0 |
| 4. |
Staybelite Ester 10 Resin |
9.0 |
| 5. |
Mineral Oil |
27.0 |
| |
|
100.0 |
Key Properties
Good peel strength
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLUBUTENES/RESINS/ POLYPROPYLENE)
| Sl. | Raw Materials | Per cent by Weight |
| 1. |
Vistanex MML-100 Isobutene Polymer |
27 |
| 2. |
Polybutene 128 Isobutene Polymer |
14 |
| 3. |
Polypropylene (Amorphous) |
13 |
| 4. |
Hercolyn D Resin |
13 |
| 5. |
Piccolyte -115 Polyterpene Resin |
13 |
| 6. |
Mineral Oil |
20 |
| |
|
100 |
Key Properties
Excellent peel strength
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYPROPYLENE/ROSIN)
| Sl. | Raw Materials | Per cent by Weight |
| 1. |
Polytac R-1000 Amorphous Polypropylene |
60.0 |
| 2. |
Tall Oil Rosin |
40.0 |
| |
|
100.0 |
Physical Constants
Brookfield Viscosity @ 340ºF: 1,100 cp
Softening Point (Ring and Ball): 300ºF (149ºC)
Key Properties
Excellent elongation
Relatively low cost
Low odour
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYPROPYLENE/ROSIN)
| Sl. | Raw Materials | Parts by wet weight | Percent by wet weight |
| 1. |
Polytac R-1000 Amorphous Polypropylene |
50.0 |
50.5 |
| 2. |
Tall Oil Rosin |
34.0 |
34.3 |
| 3. |
Paraffin Wax (190°-195°F Melting Point) |
154.0 |
15.2 |
| |
|
99.0 |
100.0 |
Physical Constants
Brookfield Viscosity @ 340ºF: 1,000 cp
Softening Point (Ring and Ball): 290ºF (143ºC)
Key Properties
Tacky and stringy
Relatively low cost
Low odour
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYPROPYLENE/ROSIN/ POLYBUTENE)
In
| Sl. | Raw Materials | Per cent by Weight |
| 1. |
Polytac R-1000 Amorphous Polypropylene |
50.0 |
| 2. |
Rosin (Hydrogenated) |
30.0 |
| 3. |
dopol H-300 Isobutene Polymer |
20.0 |
| |
|
100.0 |
Physical Constants
Brookfield Viscosity @ 340ºF: 1300 cp
Key Properties
Excellent surface tack
Relatively low cost
Low odour
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/ETHYLENE-VINYL ACETATE/POLYETHYLENE)
M
| Sl. | Raw Materials | Per cent by Weight |
| 1. |
Ethylene/Vinyl Acetate Copolymer Resin (Melt Index of 2-3) |
24.88 |
| 2. |
icrocrystalline Wax (180°F MeltingPoint) |
24.88 |
| 3. |
Epolene C-15 Polyethylene Resin |
12.44 |
| 4. |
Wingtack 115 Polyterpene Resin |
37.30 |
| 5. |
Wingstay L Antioxidant |
0.50 |
| |
|
100.00 |
Softening Point (Ring and Ball): 201ºF (94ºC)
Brookfield Viscosity @ 300ºF: 10,500 cp
Brookfield Viscosity @ 325ºF: 7,200 cp
Brookfield Viscosity @ 350ºF: 5,100 cp
Key Properties
Suitable for high tempera-Low volatility
True hot melt-Viscosity stable under
Adhesive applications prolonged heat-Good hot tack and wet ability
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/ISOPRENE-STYRENE/POLYBUTENE/RESIN)
| Sl. | Raw Materials | Parts by wet weight | Percent by wet weight |
| 1. |
Solprene 418 Plastomer |
100 |
26.88 |
| 2. |
Wingtack 95 Polyterpene Resin |
150 |
40.32 |
| 3. |
Amoco 18-210 Resin |
40 |
10.75 |
| 4. |
Indopol H-300 Isobutene Polymer |
80 |
21.51 |
| 5. |
Irganox 1010 Antioxidant/Stabilizer |
2 |
0.54 |
| |
|
372 |
100.00 |
Formulation Note
Other elastomers, besides Solprene 418, may give excellent results in similar compounds.
Physical Constants
Quick Stick Adhesion (PSTC-5): 4.1 lb
Peel Adhesion (PSTC-1): 11.4 lb
Shear Adhesion (Amoco): 135.0 sec
Key Properties
Tacky-Improved quick stick
Strengthened and reinforced-adhesion and peel
compound-adhesion
Should find application inself-stick floor tiles, special
tapes and specialty labels-Excellent shear adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/ISOPRENE-STYRENE/POLYBUTENE/RESIN)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Solprene 418 Plastomer |
100 |
26.88 |
| 2. |
Wingtack 95 Polyterpene Resin |
150 |
40.32 |
| 3. |
Amoco 18-290 Resin |
40 |
10.75 |
| 4. |
Indopol L-14 Isobutene Polymer |
80 |
21.51 |
| 5. |
Irganox 1010 Antioxidant/Stabilizer |
2 |
0.54 |
| |
|
372 |
100.00 |
Formulation Note
Other elastomers, besides Solprene 418, may give excellent results in similar compounds.
Physical Constants
Rolling Ball Tack (PSTC-6): 1.3 cm
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and speciality labels Improved rolling ball tack
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYOTERPENE/ISOPRENE-STYRENE/POLYBUTENE/RESIN)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Solprene 418 Plastomer |
100 |
26.88 |
| 2. |
Wingtack 95 Polyterpene Resin |
150 |
40.32 |
| 3. |
Amoco 18-290 Resin |
40 |
10.75 |
| 4. |
Indopol H-1500 Isobutene Polymer |
80 |
21.51 |
| 5. |
Irganox 1010 Antioxidant/Stabilizer |
2 |
0.54 |
| |
|
372 |
100.00 |
Formulation Note
Other elastomers, besides Solprene 418, may give excellent results in similar compounds.
Physical Constants
Quick Stick Adhesion (PSTC-5): 4.3 lb
Peel Adhesion (PSTC-1): 13.7 lb
Shear Adhesion (Amoco Test): 28.9 lb
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and speciality labels
Improved quick stick adhesion and peel adhesion
Good Shear Adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/ISOPRENE-STYRENE/POLYBUTENE/RESIN)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Solprene 418 Plastomer |
100 |
33.11 |
| 2. |
Wingtack 95 Polyterpene Resin |
150 |
49.67 |
| 3. |
Amoco 18-210 Resin |
40 |
13.25 |
| 4. |
Indopol L-14 Isobutene Polymer |
10 |
3.31 |
| 5. |
Irganox 1010 Antioxidant/Stabilizer |
2 |
0.66 |
| |
|
302 |
100.00 |
Formulation Note
Other elastomers, besides Solprene 418, may give excellent results in similar compounds.
Physical Constants
Quick Stick Adhesion (PSTC-5): 11.6 lb
Peel Adhesion (PSTC-1): 10.7 lb
Shear Adhesion (Amoco Test): 42.8 sec.
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and speciality labels
Improved quick stick adhesion and peel adhesion
Good Shear Adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/RESIN)
| Sl. | Raw Materials | Percent by Weight |
| 1. |
Wingtack 95 Polyterpene Resin |
47.69 |
| 2. |
Kraton 1107 Thermoplastic Crumb Rubber |
28.66 |
| 3. |
Dow 276-V2 Resin |
23.65 |
| |
|
100.00 |
Key Properties
Good hot tack and wettability
Excellent shear and peel adhesion
Low volatility
Viscosity stable under prolonged heat
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/STYRENE-BUTDIENE-STYRENE)
WT1.96
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
ingtack 76 Polyterpene Resin |
28 |
54.90 |
| 2. |
Styrene/Butadiene/Styrene Block Copolymer |
12 |
23.53 |
| 3. |
ufflo 6054 Naphthenic Oil |
10 |
19.61 |
| 4. |
Antioxidant |
1 |
| |
|
51 |
100.00 |
Physical Constants
Initial Performance:
Rolling Ball tack: 0.2 inch
180 Peel: 48 oz/inch
Dynamic Shear: 35 psi
Aged Performance:
Rolling Ball Tack: 0.2 inch
180 Peel: 51 oz/inch
Dynamic Shear: 39 psi
Key Properties
Excellent adhesive characteristics
Good heat and oxidation stability
Light colour
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/STYRENE-ISOPRENE-STYRENE/STYRENE-BUTADIENE)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Wingtack 95 Polyterpene Resin |
35.0 |
34.48 |
| 2. |
Pliolite S5-D Styrene-Butadiene Resin |
22.5 |
22.17 |
| 3. |
Styrene/Isoprene/Styrene Block Copolymer |
27.5 |
27.09 |
| 4. |
Flexon 766 Extender Oil |
15.0 |
14.78 |
| 5. |
Butyl Zimate Accelerator |
1.5 |
1.48 |
| |
|
101.5 |
100.00 |
Physical Constants
Rolling Ball Tack - Initial: 0.9 inch
Rolling Ball Tack - Aged: 0.5 inch
180º Peel - Initial: 46 oz/inch
Temperature to failure (1,000 g/in2): 372ºF
Viscosity Change (1.5 hours at 400ºF): -7.0%
Viscosity Change (2 hours at 400ºF): -10.0%
Colour - Visual: Cream
Colour - Aged 2 Hours at 400ºF: Dark Cream
Key Properties
Improvement exhibited by Pliolite S5-D Styrene-Butadiene Resin addition were:
Increased temperature to failure
Increased tack
Less percentage viscosity change
Improved aged colour
HOT MELT PRESSURE SENSITIVE ADHESIVE (POLYTERPENE/ETHYLENE-VINYL ACETATE)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
M&M 7512 Petrolatum |
40 |
34.78 |
| 2. |
Elvax 260 Ethylene/Vinyl Acetate Copolymer Resin |
30 |
26.09 |
| 3. |
Wingtack 95 Polyterpene Resin |
30 |
26.09 |
| 4. |
Wingtack 10 Polyterpene Resin |
15 |
13.04 |
| |
|
115 |
100.00 |
Physical Constants
Brookfield Viscosity (#2/20 RPM) @ 300ºF: 2,300 cp
Brookfield Viscosity (#2/20 RPM) @ 325ºF: 1,300 cp
Brookfield Viscosity (#2/20 RPM) @ 350ºF: 1,000 cp
Softening Point (Ring and Ball): 165ºF (74ºC)
Key Properties
Lowered molten viscosity with little effect on softening point
Wingtack 10 Polyterpene Resin gives the following properties to the compound:
Increased tack adhesion
Modified shear and peel strength
Helps prevent stringing on hot melt applicators and air bubble formation on roller applicators
Reduced possibility of degradation
Assists in pressure-sensitive properties
HOT MELT PRESSURE SENSITIVE ADHESIVE (RESIN/RUBBER)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100 |
32.79 |
| 2. |
Escorez 5320 Hydrocarbon Resin |
140 |
45.90 |
| 3. |
Shellflex 371 Extender Oil |
60 |
19.67 |
| 4. |
Butyl Zimate Accelerator |
5 |
1.64 |
| |
|
305 |
100.00 |
Formulation Note
The Shellflex 371 Extender Oil is added to improved the compatibility and reduce the melt viscosity of the Escorez 5320 Hydrocarbon Resin with the Kraton 1107 Thermoplastic Crumb Rubber. A better compromise between melt viscosity and pressure sensitive adhesive properties might be with less or no Shellflex 371 at all.
Physical Constants
Appearance: Transparent
Brookfield Viscosity @ 350ºF (Initial): 14,500 cp
Brookfield Viscosity @ 350ºF (Aged 72 hours at 300ºF): 10,000 cp
Percent Change in Viscosities: -31%
Rolling Ball Tack: 0.3 inch (Low values desirable)
180º Peel Adhesion: 92 oz/inch (12 inches/minute to steel)
20º Hold (½ inch Ã- ½ inch Contact Area, 400 gram Load): 63 minutes
178º Vertical Hold (½ inch Ã- ½ inch Contact Area, 1,000 gram Load): 1.3 hours
Key Properties
Somewhat higher holding power than comparative aliphatic hydrocarbon resin
Good melt stability upon aging
HOT MELT PRESSURE SENSITIVE ADHESIVE (RESIN/RUBBER)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100 |
44.44 |
| 2. |
Escorez 5280 Hydrocarbon Resin |
120 |
53.34 |
| 3. |
Butyl Zimate Antioxidant |
5 |
2.22 |
| |
|
225 |
100.00 |
Physical Constants
Brookfield Viscosity @ 350ºF: 42,500 cp
Properties of 1.5 mil Adhesive Film on 1.5 mil Polyester film:
Rolling Ball Tack: 2.0 inched (Low values desirable)
Peel Adhesion: 88 ounces/inch (12 inches/minute to steel)
Hold (½ inch Ã- ½ inch Contact Area, 400 gram Load): 740 minutes
178º Verticle Hold (½ inch Ã- ½ inch Contact Area, 1,000 gram Load): 30 hours
Key Properties
Excellent compatibility
Very good holding power
Adequate tack rating
HOT MELT PRESSURE SENSITIVE ADHESIVE (RESIN/RUBBER)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100 |
32.79 |
| 2. |
Escorez 5320 Hydrocarbon Resin |
140 |
45.90 |
| 3. |
Shellflex 371 Extender Oil |
60 |
19.67 |
| 4. |
Butyl Zimate Accelerator |
5 |
1.64 |
| |
|
305 |
100.00 |
Physical Constants
Brookfield Viscosity @ 350ºF: 14,500 cp
Properties of 1.5 mil Adhesive Film on 1.5 mil Polyester film:
Rolling Ball Tack: 0.3 inched (Low values desirable)
180º Peel Adhesion: 92 ounces/inch (12 inches/minute to steel)
Hold (½ inch Ã- ½ inch Contact Area, 400 gram Load): 63 minutes
178º Verticle Hold (½ inch Ã- ½ inch Contact Area, 1,000 gram Load): 1.3 hours
Key Properties
Soft, relatively low viscosity compound with excellent tack properties
High concentration of oil as a diluent lowers strength or holding power
HOT MELT PRESSURE SENSITIVE ADHESIVE RUBBER/POLYTERPENE /POLYBUTENE/RESIN)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100.0 |
33.22 |
| 2. |
Wingtack 95 Polyterpene Resin |
100.0 |
33.22 |
| 3. |
Amoco 18-290 Polyterpene Resin 40.0 |
13.29 |
| 4. |
Indopol L-14 Isobutene Polymer |
60.0 |
19.94 |
| 5. |
Irganox 1010 Antioxidant/Stabilizer |
1.0 |
0.33 |
| |
|
301.0 |
100.00 |
Formulation Note
Other elastomers, besides Kraton 1107, may give excellent results in similar compounds.
Physical Constants
Rolling Ball Tack (PSTC-6): 2.3 cm
Quick Stick Adhesion (PSTC-5): 2.0 lb
Peel Adhesion (PSTC-1): 2.5 lb
Shear Adhesion (Amoco Test): 1.6 sec
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and labels and where solvent-free coating provide economic or environmental advantages
Improved rolling ball tack, quick stick adhesion and peel adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE RUBBER/POLYTERPENE/ POLYBUTENE/RESIN)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100.0 |
38.31 |
| 2. |
Wingtack 95 Polyterpene Resin |
100.0 |
38.31 |
| 3. |
Amoco 18-290 Resin |
20.0 |
7.66 |
| 4. |
Indopol H-1500 Isobutene Polymer |
40.0 |
15.34 |
| 5. |
Iraganox 1010 Antioxidant/Stabilizer |
1.0 |
0.38 |
| |
|
261.0 |
100.00 |
Formulation Note
Other elastomers, besides Kraton 1107, may give excellent results in similar compounds.
Physical Constants
Quick Stick Adhesion (PSTC-5): 5.3 lb
Peel Adhesion (PSTC-1): 10.7 lb
Shear Adhesion (Amoco Test): 37.6 sec
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and labels and where solvent-free coatings provide economic or environmental advantages
Improved quick stick adhesion and peel adhesion
Good shear adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE RUBBER/POLYTERPENE/ POLYBUTENE/RESIN)
I
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100.0 |
33.22 |
| 2. |
Wingtack 95 Polyterpene Resin |
100.0 |
33.22 |
| 3. |
Amoco 18-290 Resin |
40.0 |
13.29 |
| 4. |
Indopol L-14 Isobutene Polymer |
60.0 |
19.94 |
| 5. |
rganox 1010 Antioxidant/Stabilizer |
1.0 |
0.33 |
| |
|
301.0 |
100.00 |
Formulation Note
Other elastomers, besided Kraton 1107, may give excellent results in similar compounds.
Physical Constants
Rolling Ball Tack (PSTC-6): 2.3 cm
Quick Stick Adhesion (PSTC-5): 2.0 lb
Peel Adhesion (PSTC-1): 2.5 lb
Shear Adhesion (Amoco Test): 1.6 sec
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and labels and where solvent-free coatings provide economic or environmental advantages
Improved rolling ball tack, quick sick adhesion and peel adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE RUBBER/POLYTERPENE/RESIN /POLYBUTENE)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100.0 |
35.59 |
| 2. |
Wingtack 95 Polyterpene Resin |
100.0 |
35.59 |
| 3. |
Amoco 18-290 Resin |
40.0 |
14.23 |
| 4. |
Indopol H-1500 Isobutene Polymer |
40.0 |
14.23 |
| 5. |
Irganox 1010 Antioxidant/Stabilizer |
1.0 |
0.36 |
| |
|
281.0 |
100.00 |
Formulation Note
Other elastomers, besided Kraton 1107, may give excellent results in similar compounds.
Physical Constants
Quick Stick Adhesion (PSTC-5): 4.5 lb
Peel Adhesion (PSTC-1): 12.0 lb
Shear Adhesion (Amoco Test): 32.3 sec
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and labels and where solvent-free coatings provide economic or environmental advantages
Improved quick stick adhesion and peel adhesion
Good shear adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE RUBBER/POLYTERPENE/RESIN /POLYBUTENE)
[tdIrganox 1010 Antioxidant/Stabilizer
Formulation Note
Other elastomers, besided Kraton 1107, may give excellent results in similar compounds.
Physical Constants
Quick Stick Adhesion (PSTC-5): 1.8 lb
Peel Adhesion (PSTC-1): 5.8 lb
Shear Adhesion (Amoco Test): 263.0 sec
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and labels and where solvent-free coatings provide economic or environmental advantages
Improved quick sick adhesion and peel adhesion
Excellent shear adhesion
HOT MELT PRESSURE SENSITIVE ADHESIVE RUBBER/POLYTERPENE/RESIN /POLYBUTENE)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100.0 |
39.84 |
| 2. |
Wingtack 95 Polyterpene Resin |
100.0 |
39.84 |
| 3. |
Amoco 18-290 Resin |
40.0 |
15.94 |
| 4. |
Indopol H-100 Isobutene Polymer |
10.0 |
3.98 |
| 5. |
1.0 |
0.40 |
| |
|
251.0 |
100.00 |
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100.0 |
36.36 |
| 2. |
Wingtack 95 Polyterpene Resin |
100.0 |
36.36 |
| 3. |
Amoco 18-210 Resin |
50.0 |
18.19 |
| 4. |
Indopol H-1500 Isobutene Polymer |
20.0 |
7.27 |
| 5. |
Ethyl Antioxidant 330 |
5.0 |
1.82 |
| |
|
275.0 |
100.00 |
Formulation Note
Other elastomers, besided Kraton 1107, may give excellent results in similar compounds.
Physical Constants
Rolling Ball Tack (PSTC-6): 19.3 cm
Peel Adhesion (PSTC-1): 2.4 lb
Shear Adhesion (Amoco Test): 3,309 sec
Key Properties
Tacky
Strengthened and reinforced compound
Should find application in self-stick floor tiles, speciality tapes and labels and where solvent-free coatings provide economic or environmental advantages
Improved rolling ball tack, quick sick adhesion and peel adhesion
Excellent shear adhesion
HOT MELT PRESSURE ADHESIVE (RUBBER/RESIN)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Zonarez 7115 Polyterpene Resin |
40.0 |
39.8 |
| 2. |
Styrene/Isoprene Block Copolymer |
60.0 |
59.7 |
| 3. |
Antioxidant |
0.5 |
0.5 |
| |
|
100.5 |
100.00 |
Formulation Note
Recommended application temperature is 350º to 390ºF (177º to 199ºC)
Key Properties
Improved tack and adhesionof pressure-sensitive
Improved flexibility athigh and low temperatures
propereties
Excellent stability
High quality
HOT MELT PRESSURE SENSITIVE ADHESIVE (RUBBER/RESINS)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Kraton 1107 Thermoplastic Crumb Rubber |
100 |
32.79 |
| 2. |
Escorez 5280 Hydrocarbon Resin |
100 |
32.79 |
| 3. |
Cumar LX-509 Resin |
40 |
13.11 |
| 4. |
Shellflex 371 Extender Oil |
60 |
19.67 |
| 5. |
Butyl Zimate Accelerator |
5 |
1.64 |
| |
|
305 |
100.00 |
Formulation Note
The Shellflex 371 Extender Oil is added to improve the compatibility and reduce the melt viscosity of the Escorez 5280 Hydrocarbon Resin with the Kraton 1107 Thermoplastic Crumb Rubber. A better compromise between melt viscosity and pressure sensitive adhesive properties might be with less or no Shellflex 371 at all.
Physical Constants
Appearance: Opaque
Brookfield Viscosity @ 350ºF (Initial): 11,200 cp
Brookfield Viscosity @ 350ºF (Aged 72 hours @ 300ºF): 7,500 cp
Percent Change in Viscosities: -33%
Rolling Ball Tack: 0.1 inch (Low values desirable)
180º Peel Adhesion: 76 ounces/inch (12 inches/minute to steel)
20º Hold (½ inch Ã- ½ inch Contact Area, 400 gram Load): 52 minutes
178º Vertical Hold (½ inch Ã- ½ inch Contact Area, 1,000 gram Load): 1.3 hours
Key Properties
Somewhat higher holding power than comparative aliphatic hydrocarbon resin
Good melt stability upon aging
HOT MELT LOW-COST PRESSURE SENSITIVE ADHESIVE POLYPROPYLENE/ RESIN/POLYBUTENE)
| Sl. | Raw Materials | Percent by Weight |
| 1. |
Polytac R-1000 Amorphous Polypropylene |
70.0 |
| 2. |
Escorez 1315 Hydrocarbon Resin |
20.0 |
| 3. |
Indopol H-300 Isobutene Polymer |
10.0 |
Physical Constants
Brookfield Viscosity @ 340ºF: 3,000 cp
Softening Point (Ring and Ball): 295ºF
Key Properties
Relatively low cost
Low odour
HOT MELT LOW-COST PRESSURE SENSITIVE ADHESIVE POLYPROPYLENE/ RESIN)
| Sl. | Raw Materials | Percent by Weight |
| 1. |
Polytac R-1000 Amorphous Polypropylene |
60.0 |
| 2. |
Escorez 1315 Hydrocarbon Resin |
40.0 |
| |
|
100.0 |
Key Properties
Superior bonding strength
No delamination after 24 hours at 140ºF
Relatively low cost
Low odour
HOT MELT SPRAYABLE PRESSURE SENSITIVE ADHESIVE POLYTERPENE/ STYRENE-ISOPRENE-STYRENE/STYRENE-BUTADIENE)
| Sl. | Raw Materials | Parts by weight | Percent by weight |
| 1. |
Wingtack 95 Polyterpene Resin |
40.0 |
39.41 |
| 2. |
Pliolite S5-D Styrene-Butadiene Resin |
12.5 |
12.32 |
| 3. |
Process Oil |
20.0 |
19.70 |
| 4. |
Styrene/Isoprene/Styrene Block Copolymer |
27.5 |
27.09 |
| 5. |
Butyl Zimate Accelerator |
1.5 |
1.48 |
| |
|
101.5 |
100.00 |
Formulation Notes
[ol]
Maximum application temperature is 400°F
Spray on Nordson equipment from 12 to 18 inches with 100 psi at the unit.
[/ol]
Key Properties
Fiberglass insulation was bonded to steel. The bonds passed the following aging tests:
14 days at 100ºF and 95 to 100% relative humidity
14 days at 180ºF
14 days cycling 4 hours each at -20ºF, 75ºF and 180ºF
